Magnetised Screaming Bell - Part 2 - Bell and Furnace

Now we're getting serious. The axle for the bell / furnace is completely removed, and replaced with 6 magnets (all 1/8" x 1/16" discs). Here is the detail:

Step 7 - glue a magnet in each half-arch's hole. You will need to make the hole a tiny bit larger, a round file comes in handy here.

Step 8 - making sure you're not getting the side wrong (a dry-fit is essential at this stage), put a magnet in each part of the yoke. Note in the pictures below which side to be flush with.

Step 9 - saw the bottom axle off and replace with two 1 x 2 mm discs (green arrow). Again make sure you get the magnets' sides right.

Steps 10, 11 and 12: glue two 1/8" x 1/16" magnets to either side of the bell's axle, having sawn the axle off first (pink arrows at the top). Drill a hole into the bell's top and insert a 1 x 2 mm magnet (green arrow). Finally, drill a hole in the Grey Seer's arm and insert a 2 x 0.4mm magnet in there (blue arrow at the bottom).

Step 13: drill a hole in the Grey Seer's hand and insert a 2 x 0.4mm magnet.

Step 14: drill a hole into the ornament and insert a 1 x 2 mm magnet.

Steps 15 and 16: glue two 1/8" x 1/16" magnets to either side of the furnace's axle, having sawn the axle off first (only one is shown on the picture, there is one on the other side, pink arrow at the top). Drill a hole into the furnace's top and insert a 1 x 2 mm magnet (green arrow).

Now we're getting serious. The axle for the bell / furnace is completely removed, and replaced with 6 magnets (all 1/8" x 1/16" discs). Here is the detail:

Step 7 - glue a magnet in each half-arch's hole. You will need to make the hole a tiny bit larger, a round file comes in handy here.

Step 8 - making sure you're not getting the side wrong (a dry-fit is essential at this stage), put a magnet in each part of the yoke. Note in the pictures below which side to be flush with.

Step 9 - saw the bottom axle off and replace with two 1 x 2 mm discs (green arrow). Again make sure you get the magnets' sides right.

Steps 10, 11 and 12: glue two 1/8" x 1/16" magnets to either side of the bell's axle, having sawn the axle off first (pink arrows at the top). Drill a hole into the bell's top and insert a 1 x 2 mm magnet (green arrow). Finally, drill a hole in the Grey Seer's arm and insert a 2 x 0.4mm magnet in there (blue arrow at the bottom).

Step 13: drill a hole in the Grey Seer's hand and insert a 2 x 0.4mm magnet.

Step 14: drill a hole into the ornament and insert a 1 x 2 mm magnet.

 

 

Steps 15 and 16: glue two 1/8" x 1/16" magnets to either side of the furnace's axle, having sawn the axle off first (only one is shown on the picture, there is one on the other side, pink arrow at the top). Drill a hole into the furnace's top and insert a 1 x 2 mm magnet (green arrow).

 

Magnetised Screaming Bell - part 7 - finished

I fixed the oopsie:

First sawed the handle,

Added a bit of brass rod,

Verified that it fits,

Green suffed it.

Final bit:

Dug two grooves with the knife,

Added magnets and glued and green stuffed them (they're the smallest ones, 0.4 mm),

Added magnets to the pillar.

And now onto painting.

Magnetised Screaming Bell - Part 1 - Plague Monks & Rat Ogre

So I'd started glueing the thing together in order to do a Screaming Bell, as I thought using magnets would be too difficult, and I did not want a Plague Furnace anyway. Good thing I changed my mind while the glue was not entirely set. Anyway, here is part 1 of my adventures magnetising a Screaming Bell:

Step 1 - drill holes where the blind holes for the Rat Ogre and Plague Monks are. Make sure to note which are which. I went all the way through for convenience, the idea being to put green stuff over the magnets afterwards.

Step 2 - insert the magnets. These are 1/8" x 1/16" discs, usual source.

Step 3 - put a spot of paint (solar orange foundation is still my favourite for this) onto the magnets that will connect to the Plague Monks, put the Plague Monks on to get them marked, then drill holes. Note that the holes on the picture look quite ugly - this would be because I first put the magnets the wrong way round and had to force them out (when it would have been so much easier to change the magnets on the board instead, oh well…).

Step 4 - magnets are in.

Steps 5 and 6 - do the same with the Rat Ogre.

Magnetised movement trays

Before I speak about the magnetised Screaming Bell (real soon now), here is an idea I was toying with this afternoon:

I'd built four 5x4 movement trays from Games Workshop's modular tray set (they can be seen on the previous post). As the sets are originally 10x10, I was left with a 2x10 piece.

Now the Plague Monks box has got pieces in it to build Censer Bearers, however I'd already built the full 20 that came in the battalion box as standard monks. A quick pop down the shop later, I've got 20 more monks. 10 of these will be Censer Bearers, and the 10 left will join the existing 20 monks. And so to the magnetised movement tray, to cater for my growing troops.

The arrows point to the magnets, they are the 2 x 1 mm disc magnets from PowerMagnetStore.com:

Two pieces:

They snap together nicely:

It does hold well, I would think there is little risk of a split whilst moving the trays around on the game board:

Skaven

I'm having trouble getting into IG at the moment, so decided instead to concentrate on all them Skaven I'd bought back in November. All assembled, based and undercoated (although since I sprayed them on a dark and cold evening, there are some misses and quite a bit of frosting). Now onto the Screaming Bell, with magnets.

All of them critters:

Clanrats:

Plague monks:

Stormvermin:

Thanquol and Boneripper:

2 rat ogres and a pack master:

Giant rats and pack masters (I've managed to misplace one of my 6 giant rats…)

Queek Headtaker and a Warlord I bought earlier this year:

Now at some point I really ought to be looking at the rules and see what I can do with them…

 

I'm having trouble getting into IG at the moment, so decided instead to concentrate on all them Skaven I'd bought back in November. All assembled, based and undercoated (although since I sprayed them on a dark and cold evening, there are some misses and quite a bit of frosting). Now onto the Screaming Bell, with magnets.

All of them critters:

Clanrats:

Plague monks:

Stormvermin:

Thanquol and Boneripper:

2 rat ogres and a pack master:

Giant rats and pack masters (I've managed to misplace one of my 6 giant rats…)

Queek Headtaker and a Warlord I bought earlier this year:

Now at some point I really ought to be looking at the rules and see what I can do with them…

Leman Russ Demolisher Punisher Executioner

So, I've got a new toy. It's a Leman Russ Demolisher:

It's also a Leman Russ Executioner:

And, well, it's a Leman Russ Punisher too:

Or to put it another way, I've been busy with magnets. As per before, I got them from http://www.powermagnetstore.com. I used 1/8" x 1/16" discs.

First I dealt with the turret: I pierced the hinge of the door, and slid a piece of .8mm brass rod in, so the top could be opened and closed. I then glued a piece of plasticard to the bottom of the hatch.

I assembled the tank commander and sawed off the sides so it could fit in the turret. I then pierced two holes in the base and glued magnets in there. I put a dab of paint on both magnets (Macharius Solar Orange, as it's nicely thick and bright), and gently pressed the commander in the hatch. With that done I had nice dots on the plasticard. Two more holes through the dots and I had magnets glued in place.

Then it was time for the main guns. One magnet in the base, a spot of paint again, and I pressed all three main guns in turn against it (note that I filled the hole in the base of the Punisher cannon with green stuff first).

So now I had 3 magnetised main guns:

It was time to deal with the rear of the turret - same story as before, holes, paint and green stuff:

(note the magnet used above is a 2 x 1mm disc)

Here is the result:

Magnetised Screaming Bell - part 6 - oopsie

One last bit to magnetise - should be easy with a couple of 1 x 2 mm magnets on the arch, and .4 x 2 mm ones on the piece.

Now onto the oopsie:

Ah well, I'll just have to do a bit more sawing and sculpting to fix this.